ISO 4892-1:2016

本頁面標準信息均來源于網絡收集，或由參與標準制定的供應商提供，只作為參考使用，為確保測試結果的準確性、節省您的時間，如需ISO 4892-1:2016標準詳細信息或ISO 4892-1:2016具體測試方法，歡迎致電與我們技術人員聯系或給我們留言，我們將為您相關的技術支持。

ISO 4892-1:2016國際標準以“塑料—暴露于實驗室光源的方法”為總標題，由以下部分組成：

第1部分：通則;

第2部分：氙弧燈;

第3部分：熒光紫外燈;

第4部分：開放式碳弧燈，紫外光老化試驗箱。

ISO 4892-1:2016在后續部分詳細描述了和暴露操作方法的選擇有關的信息和指導。它還描述了用于將塑料暴露于實驗室光源的設備的一般性能要求。有關人工加速風化或人造加速輻射裝置生產性能要求的信息。

在ISO 4892的這一部分中，“光源”一詞是指發出紫外線輻射、可見輻射、紅外線輻射或這些輻射的任何組合的輻射源。

ISO 4892-1:2016還提供了從人工加速老化或人工加速輻射暴露數據的解釋信息。在ISO 4582中給出了關于塑料暴露后的性能變化和報告這些結果變化的方法的更具體的信息。

ISO 4892-1:2016英文簡介

ISO 4892-1:2016 provides information and general guidance relevant to the selection and operation of the methods of exposure described in detail in subsequent parts. It also describes general performance requirements for devices used for exposing plastics to laboratory light sources. Information regarding performance requirements is for producers of artificial accelerated weathering or artificial accelerated irradiation devices.

NOTE In this part of ISO 4892, the term "light source" refers to radiation sources that emit UV radiation, visible radiation, infrared radiation or any combination of these types of radiation.

ISO 4892-1:2016 also provides information on the interpretation of data from artificial accelerated weathering or artificial accelerated irradiation exposures. More specific information about methods for determining the change in the properties of plastics after exposure and reporting these results is given in ISO 4582.

1 Scope

This part of ISO 4892 provides information and general guidance relevant to the selection and operation of the methods of exposure described in detail in subsequent parts. It also describes general performance requirements for devices used for exposing plastics to laboratory light sources. Information regarding performance requirements is for producers of artificial accelerated weathering or artificial accelerated irradiation devices.

NOTE In this part of ISO 4892, the term “light source” refers to radiation sources that emit UV radiation, visible radiation, infrared radiation or any combination of these types of radiation.

This part of ISO 4892 also provides information on the interpretation of data from artificial accelerated weathering or artificial accelerated irradiation exposures. More specific information about methods for determining the change in the properties of plastics after exposure and reporting these results is given in ISO 4582.

2 Normative references

The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.

ISO 291, Plastics — Standard atmospheres for conditioning and testing

ISO 293, Plastics — Compression moulding of test specimens of thermoplastic materials

ISO 294-1, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens

ISO 294-2, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 2: Small tensile bars

ISO 294-3, Plastics — Injection moulding of test specimens of thermoplastic materials — Part 3: Small plates

ISO 295, Plastics — Compression moulding of test specimens of thermosetting materials

ISO 2818, Plastics — Preparation of test specimens by machining

ISO 3167, Plastics — Multipurpose test specimens

ISO 4582, Plastics — Determination of changes in colour and variations in properties after exposure to daylight under glass, natural weathering or laboratory light sources

ISO 4892-2, Plastics — Methods of exposure to laboratory light sources — Part 2: Xenon-arc lamps

ISO 4892-3, Plastics — Methods of exposure to laboratory light sources — Part 3: Fluorescent UV lamps

ISO 4892-4, Plastics — Methods of exposure to laboratory light sources — Part 4: Open-flame carbon-arc lamps

ISO 9370, Plastics — Instrumental determination of radiant exposure in weathering tests — General guidance and basic test method

3 Terms and definitions

For the purposes of this document, the following terms and definitions apply.

NOTE Definitions of other terms that are related to weathering tests are found in Reference [2].

3.1control

material which is of similar composition and construction to the test material and which is exposed at the same time for comparison with the test material

Note 1 to entry: An example of the use of a control material would be when a formulation different from one currently being used is being evaluated. In that case, the control would be the plastic made with the original formulation.

3.2file specimen

portion of the material to be tested which is stored under conditions in which it is stable and which is used for comparison between the exposed and unexposed states

3.3artificial accelerated weathering

exposure of a material in a laboratory weathering device to conditions which may be cyclic and intensified compared with those encountered in outdoor or in-service exposure

Note 1 to entry: This involves a laboratory radiation source, heat and moisture (in the form of relative humidity and/or water spray, condensation or immersion) in an attempt to produce more rapidly the same changes that occur in outdoor exposure.

Note 2 to entry: The device may include means for control and/or monitoring of the light source and other weathering parameters. It may also include exposure to special conditions, such as acid spray to simulate the effect of industrial gases.

3.4artificial accelerated irradiation

exposure of a material to a laboratory radiation source intended to simulate window-glass-filtered solar radiation or radiation from interior lighting sources and where specimens may be subjected to relatively small changes in temperature and relative humidity in an attempt to produce more rapidly the same changes that occur when the material is used in an indoor environment

Note 1 to entry: These exposures are commonly referred to as fading or lightfastness tests.